View BCM1113_452638.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

BCM1113
(R)
ENTERPRISE IP PHONE CHIP
FEATURES SUMMARY OF BENEFITS
* The BCM1113 is the most highly integrated silicon solution
targeted for midrange Voice-over IP enterprise phones * The BCM1113 integrates: * 87.5-MHz MIPS32TM CPU (96 DMIPS) with 8K I-cache and 4K D-cache * Superscalar 108-MHz ZSP DSP with dual-MAC (216 MIPS), 48K instruction, and 32K data RAM * Three-port 10/100BASE-T Ethernet switch with 64K buffer memory * Two 10/100BASE-T Ethernet PHYs with in-line power over Ethernet support * Three wideband audio ADCs and DACs * 9 x 9 keyscan controller * Ethernet status LED driver * TDM IOM-2(R) port * Two UARTs * Two high-speed serial ports * General purpose I/O * Interrupt control unit * DMA support unit * SDRAM interface * External bus interface * IEEE 1149.1 (JTAG) * 0.18 process technology, 1.8/3.3V
* 10/100BASE-T Ethernet Switch with 802.1p/Q support
* 802.1p priority queuing ensures QoS for voice packets and minimizes latency * Supports modification of 802.1p priority tags on packets to enforce priority tagging rules * 802.1Q VLAN support allows for segmenting physical networks into multiple logical networks * MIPS32 CPU not burdened by data packet processing, leaving more cycles for application program * Enables wire-speed non-blocking operation * Blocks unnecessary traffic by learning local MAC addresses * Segments network, preventing any restriction on number of hops * 87.5-MHz MIPS32 CPU and 108-MHz DSP Support * VxWorks Operating System * SIP, H.323, H.248/Megaco, and MGCP * G.711, G.726, G.729A/AB/E, G.723.1/A, G.728, G.722.1 and BroadVoice(R) * Full-duplex speakerphone operation * Handset echo suppression * Two- and three-channel conferencing using complex vocoders * Enhanced Packet Loss Concealment * Paging (via a G.711 channel) * User application software * 10/100BASE-T Ethernet MACs and PHYs * Integrates support for Cisco in-line power specification * Compliant with 802.3af power over Ethernet standard * Provides auto-MDI/MDIX, enabling the use of straight or crossover cables in either port * Wideband audio CODECs * Enables support of emerging wideband vocoding standards
* 1.1W peak, 0.3W - 0.8W standby modes * 256-pin PBGA package enables 4-layer PCB designs * Pin and software compatible with the BCM1101, BCM1113R,
BCM1115, and BCM1115R ICs
HARDWARE PLATFORMS
* BCM91101 reference platform
* Ethernet IP phone reference platform for midrange IP Phones designs
OVERVIEW BCM1113 VoIP Ethernet CPE Engine
Master SPI Port External Interrupt Controller Keypad Scan Controller [or 18 GPIOs]
UART 0
UART 1
18 GPIOs
Peripheral Bus
IPB Bridge
Watchdog Timer
Timers MIPS JTAG ZSP JTAG
MIPS32 CPU + 8K I-Cache + 4K D-Cache
High Speed Serial Port 2
100-MHz CPU System Bus
Analog Processor Module
CODEC Channel 3 CODEC Channel 2 CODEC Channel 1 16-bit D/A 16-bit A/D
48 KB of Program Memory ZSP DSP 32 KB of Data Memory
High Speed Serial Port 1 TDM (IOM-2) Port 50-MHz External Bus Interface
Flash/ EPROM
10/100BASE-T Auto-MDIX PHY 10/100BASE-T Auto-MDIX PHY
port 0 Three-Port Ethernet Switch port 1 port 2 SDRAM Interface SDRAM
Ethernet LED Driver
64 KB of Buffer Memory
DMA Arbiter
The Broadcom BCM1113 is a highly integrated IC targeted for the midrange Enterprise Voice-over IP market. Key modules integrated in the BCM1113 include: * MIPS32 87.5-MHz processor with 8K 2-way set associative I-cache and a 4K 2-way associative D-cache. This MCU supports the VoIP protocol stacks, jitter buffer management, and application program. Programming is done in C, on top of Broadcom's object-oriented signal processing API. * ZSP 108-MHz DSP with 48-KB instruction and 32-KB data RAM. The DSP supports a wide range of vocoders, acoustic echo cancellation for full-duplex speakerphone, fax modems, and a variety of telephony algorithms (e.g., DTMF and Call Progress Tones). * Analog codecs. Three ADCs and DACs are integrated, eliminating the need for an analog switch to allow the sharing of a codec between multiple interfaces.
* 10/100BASE-T Ethernet switch, media access controllers, and transceivers. The three-port Ethernet switch integrates three fullduplex capable Media Access Controllers (MACs), a serial management port, an address resolution engine, a non-blocking switch controller, 64K of internal switch memory, 802.1p prioritization for voice packets, 802.1Q VLAN support for segmenting physical networks into multiple logical networks, and a set of Management Information Base (MIB) statistics registers. The two transceivers perform all of the functions for 100BASE-T Ethernet in full- or half-duplex mode over Category (CAT) 5 twistedpair cable and 10BASE-T Ethernet in full- or half-duplex mode over CAT 3, 4, or 5 twisted-pair cable. They support auto-MDI/MDIX detection to allow the use of any cable type in either port. The transceivers also integrate support for in-line powering over Ethernet. The BCM1113 integrates all the key silicon components of an Ethernet IP Phone into a single device and is pin and software compatible with the BCM1101. The BCM1113 is suited for SOHO Voice-over IP phone products that require mid-range application feature sets (e.g., basic user applications operating on 2-line character displays) while still requiring the same voice quality and reliability of higher end IP phone products.
Broadcom(R), the pulse logo, Connecting everything(R), the Connecting everything logo, and BroadVoice(R) are trademarks of Broadcom Corporation and/or its affiliates in the United States, EU and/or certain other countries. Any other trademarks or trade names mentioned are the property of their respective owners.
(R)
BROADCOM CORPORATION 16215 Alton Parkway, P.O. Box 57013 Irvine, California 92619-7013
(c) 2005 by BROADCOM CORPORATION. All rights reserved. 1113-PB01-R 02/01/05
Phone: 949-450-8700 Fax: 949-450-8710 E-mail: info@broadcom.com Web: www.broadcom.com

▲Up To Search▲

Price & Availability of BCM1113

	To Download BCM1113 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .